Software, CAD and Engineering Disclaimer
Provider: Bevan Williams trading as FenceCalc Pro™, ABN 65 143 534 309
Contact: support@fencecalcpro.com.au
Effective: On publication. The effective date is shown with this version at its permanent address on fencecalcpro.com.au.
Version: 1.1 — 14 November 2026
This disclaimer forms part of the Agreement described in our Terms of Service. Nothing in it limits your rights under the Australian Consumer Law, including our obligation to supply the service with due care and skill.
1. FenceCalc Pro is an estimating and drafting tool
FenceCalc Pro helps fencing contractors estimate, price, order, draw and record work. It calculates from the information you give it — measurements, fence types, prices, margins and settings — using general estimating rules. It is a tool for a person who knows the trade, not a replacement for that person's judgement.
2. Calculations, prices and quantities
- Quantities are estimates. Material call-ups, cutting lists and purchase orders are calculated from what you enter and from general rules. Check them against the site and the job, and allow for waste, damage, stock lengths and site conditions.
- Prices are yours. FenceCalc Pro uses the prices you enter or import. Check imported prices against your supplier's current price list, and import prices excluding GST. If a price is missing, FenceCalc Pro shows the item as UNPRICED — it never treats a missing price as $0.00. Do not send a quote until every item you intend to charge for is priced.
- How figures are kept. FenceCalc Pro works with prices excluding GST. Every dollar amount is kept to two decimal places: supplier prices, costs, the rates FenceCalc Pro calculates (including rates per metre), quotes, purchase orders and claims. The first two decimal places are kept and anything after them is dropped, never rounded up. A selling rate you type is never changed, and it must be entered to the cent. Quantities and measurements keep their full precision. Issued documents keep the values they were issued with.
- Margins and selling rates are your decisions. FenceCalc Pro shows calculated figures to help you decide; it does not decide what you charge.
- Check every total on every document before you send it.
3. Engineering rules are general rules
The engineering rules in FenceCalc Pro — such as post sizes, post spacing, footing sizes, rail and bracing arrangements — are general estimating rules. They are not a site-specific engineering design, an engineering certification, or a statement that a fence complies with any law or standard.
They do not take account of every factor that can matter on a particular site, including soil and ground conditions, slope, wind exposure, retaining, loads from attached structures, nearby trees and services, or the requirements of a particular product.
Where FenceCalc Pro refers to an Australian Standard (for example, the AS 1725 series or AS 4687:2022), the reference is for identification only. A reference to a standard is not a statement that an output or the finished work meets it.
You are responsible for making sure each fence and gate you build complies with:
- the building laws and the National Construction Code where they apply;
- the Australian Standards that apply to the work, including pool-safety barrier requirements;
- local government and planning requirements, and dividing-fence laws;
- manufacturers' installation instructions and warranty conditions; and
- any engineering design required for the work — obtain one from a qualified engineer where the job needs it.
4. Drawings, CAD and fabrication outputs
- Site plans and runs traced on a map, plan or photo are approximate. Map images can be out of date or misaligned. Measure on site before ordering or building. Drawings are not survey plans and do not establish where a boundary is.
- Gate and panel drawings, cutting lists, DXF, SVG and PDF files and workshop packs are drafting and fabrication aids. Check every dimension, quantity, clearance and hardware selection before anything is cut, ordered or installed.
- Drawings marked "SCHEMATIC ONLY — NOT FOR FABRICATION" must not be used to fabricate. That mark appears where the specification is incomplete.
- Values shown as NOT SPECIFIED or TO BE CONFIRMED have not been established from an approved catalogue or technical data entry. Resolve them before the drawing is used.
- Hardware selections and ratings come from catalogue entries. Confirm them against the manufacturer's current data. Calculated figures, such as gate-weight effects and swing clearances, depend on the values entered and do not account for site conditions.
5. Site safety
FenceCalc Pro does not assess site safety. Before digging, locate underground services. Follow work health and safety laws, safe work method statements and your own safety procedures. Safety documents you upload or produce in FenceCalc Pro remain your responsibility to check and keep current.
6. Tax, legal and business documents
- GST on your quotes and purchase orders. FenceCalc Pro is designed for businesses registered for GST. It adds GST at 10% to the final total of each new client quote and purchase order, kept to two decimal places like every dollar amount; this does not change with a company setting. If your business is not registered for GST, or a supply is not taxable, you must check each document before issuing it. FenceCalc Pro does not give tax advice; ask your accountant. This is separate from GST on our own Fees, which we do not charge.
- FenceCalc Pro supplies no contract terms for your clients. Your quote is your offer. Your terms of trade, warranties and payment terms are yours to set, ideally with advice. Any suggested wording you adopt becomes yours.
- Time and attendance records are records only. FenceCalc Pro does not calculate or approve pay, and it does not check award or employment-law compliance.
7. Client-facing documents
Documents you send to your clients carry your business identity, not ours. They must not state or imply that FenceCalc Pro designed, certified or approved the work.
8. Short form for drawings and workshop packs
Estimating and drafting aid only. Not an engineered or certified design. References to Australian Standards are for identification only and do not indicate compliance. Items marked NOT SPECIFIED, TO BE CONFIRMED or SCHEMATIC ONLY must be resolved before fabrication. Verify all dimensions, quantities and hardware on site and against manufacturers' data.
9. Your rights are not affected
This disclaimer explains how FenceCalc Pro is meant to be used. It does not limit any right you have under the Australian Consumer Law. Our liability is dealt with in clauses 9 and 10 of the Terms of Service.